Sharp Error Codes






A C E F H L U

Code Description Comment
AO-01 PCU PWB ROM error Simulation Code - 16
AO-02 SCU PWB ROM error Simulation Code - 16
AO-10 Color profile error Simulation Code - 16
AO-11 Firmware version inconsistency (MFP - PCU) Simulation Code - 16
AO-15 Incompatible DSK BOOT and program firmware Simulation Code - 16
AO-16 Data error of the energy-saving NIC controller firmware in the SD card Simulation Code - 16
AO-20 Conflict firmware and EEPROM data version (MFP) Simulation Code - 16
AO-21 Conflict firmware and EEPROM data version (PCU) Simulation Code - 16
AO-22 Conflict firmware and EEPROM data version (SCU) Simulation Code - 16
C1-00 Charge corona error Power machine OFF at wall for 10 seconds
C1-10 Main charger trouble (Black) Power machine OFF at wall for 10 seconds
C1-11 Main charger trouble (Cyan) Power machine OFF at wall for 10 seconds
C1-12 Main charger trouble (Magenta) Power machine OFF at wall for 10 seconds
C1-13 Main charger trouble (Yellow) Power machine OFF at wall for 10 seconds
C1-14 Main charger trouble (Colour) MX series only Power machine OFF at wall for 10 seconds
CB3 Abnormal Tray Lift Motor Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
CE-00 The other communication error has occurred reboot
CE-01 The print server card (AR-NC3D) is not installed or defective Engineer request
CE-02 The specified mail server or the FTP server is not found IT Problem
CE-03 The specified server does not correspond during image transmission IT Problem
CE-04 The entered account name of the FTP server or the password is invalid IT Problem
CE-05 The entered directory of the FTP server is invalid IT Problem
CH Steady Open front and side doors close side and front IT Problem
CH Flashing Toner cartridge isnt installed Install and check toner
CH-00 Check developer reboot No Developer cartridge AR/ARM series only
CH-01 Check toner reboot No Toner cartridge AR/ARM series only
CH-02 Check drum reboot No Drum cartridge AR/ARM series only
C4-00/02/03 PTC trouble (TC high voltage PWB trouble) Crop 16
E1-00 IMC PWB communication trouble Restart/Crop 16
E1-10 IMC PWB trouble Restart/Crop 16
E1-11 IMC ASIIC error Restart/Crop 16
E1-13 IMC PWB flash ROM error Restart/Crop 16
E1-16 IMC PWB DIMM memory read/write check error Restart/Crop 16
E1-81 Interface error in communication with IMC PWB (Parity) Restart/Crop 16
E1-82 Interface error in communication with IMC PWB (Overrun) Restart/Crop 16
E1-84 Interface error in communication with IMC PWB (Framing) Restart/Crop 16
E6-11 CSI Shading Trouble (white correction) Reboot
E7-01 Duplex model memory error REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
E7-02 Laser trouble REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
E7-03 HDD trouble REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
E7-04 HDD-ASIC trouble REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
E7-05 Local memory access error REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
E7-06 Image data decode error REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
E7-07 SD card error REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
E7-10 Shading trouble (Black correction) REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
E7-11 Shading trouble (White correction) REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
E7-14 CCD-ASIC error REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
E7-16 Abnormal laser output REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
E7-20 Laser beam Sensor trouble (Black) REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
E7-21 Laser beam Sensor trouble (Cyan) REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
E7-22 Laser beam Sensor trouble (Magenta) REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
E7-23 Laser beam Sensor trouble (Yellow) REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
E7-24 Laser beam detection trouble (Black) REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
E7-25 Laser beam detection trouble (Cyan) REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
E7-26 Laser beam detection trouble (Magenta) REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
E7-27 Laser beam detection trouble (Yellow) REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
E7-28 LSU - PCU connection error REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
E7-29 LSU ASIC frequency error REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
E7-30 ICU PWB FLASH ROM trouble REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
E7-49 Water Mark data error REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
E7-50 Combination error between PWB and firmware (PCU PWB detection) REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
E7-55 PCU PWB information sum error REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
E7-60 Combination error between PWB and firmware (MFPC PWB detection) REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
E7-61 Combination error between the MFPC PWB and the PCU PWB REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
E7-65 MFP EEPROM sum check error REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
E7-80 MFP - SCU PWB communication error REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
E7-89 Communication error between MFPC PWB CPU and energy-saving NIC controller REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
E7-90 MFP - PCU PWB communication error REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
E7-91 FAX reception image data error REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
E7-92 Copy image data error REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
E7-93 Copy, image send, filing, print image data process error REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
E7-94 Image file data process error (when importing file data) REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
E7-95 Printer PWB DIMM memory check error REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
E7-96 MFPC PWB DIMM memory check error REBOOT - if fault returns on first use consider disabling function or informing user not to use function that is causing problem until engineer arrives
EE-EC Automatic toner density adjustment error Check Toner and Crop - Change toner if required
EE-EL Automatic toner density adjustment error (Over toner) Check Toner and Crop - Change toner if required
EE-EU Automatic toner density adjustment error (Under toner) Check Toner and Crop - Change toner if required
F1-00 Finisher communication trouble Remove paper jam Reboot
F1-02 Finisher transport motor abnormality / Mail-bin stacker transport motor abnormality Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-03 Console Finisher Paddle Motor Trouble Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-06 Finisher shift motor trouble Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-08 Finisher staple shift motor trouble Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-09 Finisher load capacity sensor trouble Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-10 Finisher staple unit operation trouble Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-11 Finisher 1 pusher motor trouble / Finisher 2 boomerang rotation abnormality Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-12 Mail-bin stacker gate trouble Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-15 Finisher 1 Elevator motor trouble/Finisher 2 elevator motor trouble Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-18 Tray3 paper exit paddler operation trouble Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-19 Finisher pre-alignment motor abnormality Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-20 Console finisher (AR-FN7) rear alignment motor trouble Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-21 Finisher interface fan motor abnormality Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-22 Finisher rear edge assist motor trouble Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-23 Shutter trouble Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-30 Console finisher (AR-FN7) communication trouble Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-31 Console finisher (AR-FN7) Fold sensor trouble Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-32 Communication trouble between the console finisher (AR-FN7) and the punch unit (AR-PN1) Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-33 Console finisher (AR-FN7) Punch (AR-PN1) side registration motor trouble Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-34 Console finisher (AR-FN7) Punch (AR-PN1) motor trouble Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-35 Console finisher (AR-FN7) Punch (AR-PN1) side registration sensor trouble Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-36 Console finisher (AR-FN7) Punch (AR-PN1) Timing sensor trouble Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-37 Console finisher (AR-FN7) backup RAM trouble Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-38 Console finisher (AR-FN7) Punch (AR-PN1) backup RAM trouble Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-41 Positioning plate motor trouble Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-42 Guide motor trouble Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-43 Side alignment motor trouble Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-44 Stitch motor rear trouble Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-45 Stitch motor front trouble Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-46 Paper pushing motor trouble Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-50 Finisher incompatibility trouble Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-51 Sensor connector connection trouble Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-52 Micro SW trouble Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-60 Communication trouble between the finisher and the inserter Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-61 Inserter EEPROM trouble Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-62 Inserter reverse sensor trouble Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-80 Console finisher (AR-FN7) Mail-bin stacker (AR-MS1) power abnormality Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-81 Console finisher transport motor abnormality Turn Off Pull out finisher unit, check for blockage push unit back in Turn On
F1-87 Staple Rotation Motor Trouble Check staple cartridge for blockages Reboot Finisher
F2-00 Toner control sensor open Crop
F2-02 Toner motor connector unconnected Check Toner and Crop - Change toner if required
F2-04 Improper cartridge (life cycle error, etc.) Check Toner and Crop - Change toner if required
F2-05 CRUM error Check Toner and Crop - Change toner if required
F2-22 Discharge lamp trouble (K) Check Toner and Crop - Change toner if required
F2-23 Discharge lamp trouble (C) Check Toner and Crop - Change toner if required
F2-24 Discharge lamp trouble (M) Check Toner and Crop - Change toner if required
F2-25 Discharge lamp trouble (Y) Check Toner and Crop - Change toner if required
F2-31 Process control trouble (Drum surface reflection) Check Toner and Crop - Change toner if required
F2-32 Process control trouble (Drum mark) Check Toner and Crop - Change toner if required
F2-37 Drum marking sensor gain adjustment error Check Toner and Crop - Change toner if required
F2-39 Process thermistor breakdown Check Toner and Crop - Change toner if required
F2-40 Toner density sensor trouble (BLACK) Check Toner and Crop - Change toner if required
F2-41 Toner density sensor trouble (CYAN) Check Toner and Crop - Change toner if required
F2-42 Toner density sensor trouble (MAGENTA) Check Toner and Crop - Change toner if required
F2-43 Toner density sensor trouble (YELLOW) Check Toner and Crop - Change toner if required
F2-44 Toner density sensor trouble (BLACK) Check Toner and Crop - Change toner if required
F2-45 Color image density sensor trouble Check Toner and Crop - Change toner if required
F2-49 LSU thermistor trouble Check Toner and Crop - Change toner if required
F2-50 K drum phase sensor trouble Check Toner and Crop - Change toner if required
F2-51 CL drum phase sensor trouble Check Toner and Crop - Change toner if required
F2-58 Temperature/humidity sensor trouble (HUD_M/TH_M) Check Toner and Crop - Change toner if required
F2-64 Toner supply operation trouble(Black) Check Toner and Crop - Change toner if required
F2-65 Toner supply operation trouble (Cyan) Check Toner and Crop - Change toner if required
F2-66 Toner supply operation trouble (Magenta) Check Toner and Crop - Change toner if required
F2-67 Toner supply operation trouble (Yellow) Check Toner and Crop - Change toner if required
F2-70 Improper toner cartridge detection BLACK Check Toner and Crop - Change toner if required
F2-71 Improper toner cartridge detection CYAN Check Toner and Crop - Change toner if required
F2-72 Improper toner cartridge detection MAGENTA Check Toner and Crop - Change toner if required
F2-73 Improper toner cartridge detection YELLOW Check Toner and Crop - Change toner if required
F2-74 Toner cartridge CRUM error BLACK Check Toner and Crop - Change toner if required
F2-75 Toner cartridge CRUM error CYAN Check Toner and Crop - Change toner if required
F2-76 Toner cartridge CRUM error MAGENTA Check Toner and Crop - Change toner if required
F2-77 Toner cartridge CRUM error YELLOW Check Toner and Crop - Change toner if required
F2-78 (Transfer belt substrate reflection rate abnormality) Check Toner and Crop - Change toner if required
F2-91 High density process control high voltage error (BK) Check Toner and Crop - Change toner if required
F2-92 High density process control high voltage error (C) Check Toner and Crop - Change toner if required
F2-93 High density process control high voltage error (M) Check Toner and Crop - Change toner if required
F2-94 High density process control high voltage error (Y) Check Toner and Crop - Change toner if required
F3-12 Copier top stage CS lift up trouble/Tray 1 lift-up trouble Empty trays of paper then Crop 15
F3-22 Copier bottom stage CS lift up trouble/Tray 2 lift-up trouble Empty trays of paper then Crop 15
F3-32 Copier bottom stage CS lift up trouble/Tray 3 lift-up trouble Empty trays of paper then Crop 15
F3-42 Copier bottom stage CS lift up trouble/Tray 4 lift-up trouble Empty trays of paper then Crop 15
F5-02 Copy lamp lighting abnormality Crop
F6-00 MFPC PWB - FAX communication trouble REBOOT- if fault returns advise user not to use Fax function till engineer arrives
F6-01 FAX control PWB EEPROM read/write error REBOOT- if fault returns advise user not to use Fax function till engineer arrives
F6-04 FAX MODEM operation trouble REBOOT- if fault returns advise user not to use Fax function till engineer arrives
F6-21 Improper combination of TEL/LIU PWB and FAX soft switch REBOOT- if fault returns advise user not to use Fax function till engineer arrives
F6-30 FAX 1-chip microprocessor access error (FAX detection) REBOOT- if fault returns advise user not to use Fax function till engineer arrives
F6-97 Incompatibility between FAX control PWB and the main machine REBOOT- if fault returns advise user not to use Fax function till engineer arrives
F6-98 Incompatibility between the FAX control PWB destination and the main machine destination REBOOT- if fault returns advise user not to use Fax function till engineer arrives
F7-01 Fax board EEPROM read/write error Reboot
F9-00 Printer communication trouble Reboot if not worked refer to IT
F9-01 PRT DRAM trouble Reboot if not worked refer to IT
F9-02 PRT Centroport check error Reboot if not worked refer to IT
F9-03 Network Card trouble Reboot if not worked refer to IT
F9-04 Printer program error Reboot if not worked refer to IT
F9-05 Short of memory capacity on the ICU PWB Reboot if not worked refer to IT
F9-10 PRT SCSI LSI abnormality Reboot if not worked refer to IT
F9-88 Timeout Error Reboot if not worked refer to IT
F9-90 Printer communication trouble Reboot if not worked refer to IT
F9-91 Communication error between MFP and the printer section when booting Reboot if not worked refer to IT
F9-92 Printer (section) PWB hardware error Reboot if not worked refer to IT
H2-00 Thermistor open trouble (TH_UM_AD2) CROP 14
H2-01 Thermistor open trouble (TH_LM) CROP 14
H2-02 Thermistor open trouble (TH_US) CROP 14
H2-03 Thermistor open trouble (TH_UM_AD1) CROP 14
H3-00 Fusing section high temperature trouble (TH_UM) CROP 14
H3-01 Fusing section high temperature trouble (TH_LM) CROP 14
H3-02 Fusing section high temperature trouble (TH_US) CROP 14
H3-10 Main heater lamp abnormally high temperature soft detection trouble CROP 14
H4-00 Fusing section low temperature trouble (TH_UM_AD2) CROP 14
H4-01 Fusing section low temperature trouble (TH_LM) CROP 14
H4-02 Fusing section low temperature trouble (TH_US) CROP 14
H4-30 Thermistor input circuit trouble (TH_UM) CROP 14
H5-01 5-time continuous POD1 not-reaching JAM detection Clear paper jam Crop 14
H5-02 Fusing thermistor abnormality Clear paper jam Crop 14
H7-10 Recovery error from low fuser temp. (TH_UM_AD2) CROP 14
H7-11 Recovery error from low fuser temp. (TH_LM) CROP 14
H7-12 Recovery error from low fuser temp. (TH_US) CROP 14
H6 Low oil in fuser (ARC models only) Add Fuser oil
L1-00 Scanner feed trouble Turn Scan lock to unlock Reboot
L3-00 Scanner return trouble Crop/Reboot
L4-01 Paper feed motor trouble CROP 14
L4-02 Drum motor lock detection CROP 14
L4-03 Fusing motor trouble CROP 14
L4-04 Development motor trouble (Black) CROP 14
L4-05 Development motor trouble (Colour) CROP 14
L4-06 Transfer belt lift trouble CROP 14
L4-11 Shift motor trouble CROP 14
L4-12 Secondary transfer separation trouble CROP 14
L4-16 Fusing pressure release trouble CROP 14
L4-31 Paper exit cooling fan trouble CROP 14
L4-32 Power source cooling fan trouble CROP 14
L4-35 Fusing cooling fan trouble CROP 14
L4-43 Paper exit cooling fan 3 trouble CROP 14
L4-50 Process fan trouble CROP 14
L4-51 Process fan 2 trouble CROP 14
L6-10 Polygon motor lock detection Engineer required
L8-01 No fullwave signal CROP 16
L8-02 Full-wave signal width abnormality CROP 16
L8-20 Communication error of MFPC PWB/LSU mother board PC Personal counter not detected CROP 16
U0 ICU_OPE Communication trouble Crop Reboot
U1-01 Fax Battery abnormality Crop/Replace battery
U1-02 RTC read abnormality (common with FAX, on ICU PWB) Engineer Required
U2-00 EEPROM Read/write error Crop 16
U2-05 HDD/MFPC PWB SRAM contents inconsistency Crop 16
U2-10 MFPC PWB SRAM user authentication index check sum error Crop 16
U2-11 Counter sum check error (MFP control EEPROM) Crop 16
U2-12 Adjustment value check sum error (MFP control EEPROM) Crop 16
U2-22 MFPC section SRAM memory sum check error Crop 16
U2-23 MFPC section SRAM memory individual data check sum error Crop 16
U2-24 SRAM memory user authentication counter check sum Crop 16
U2-30 MFPC PWB and PCU PWB manufacturing No. data inconsistency Crop 16
U2-40 CRUM chip communication error Crop 16
U2-50 HDD section individual data sum check error Crop 16
U2-60 Watermark check error Crop 16
U2-80 Scanner section EEPROM read/write error Crop 16
U2-81 Scanner section memory sum check error Crop 16
U2-90 PCU section EEPROM read/write error Crop 16
U2-91 PCU section memory sum check error Crop 16
U5-00 RADF/SPF/RSPF communication trouble Crop
U5-01 RADF resist sensor trouble Crop
U5-02 RADF eject/inversion sensor trouble Crop
U5-03 RADF timing sensor trouble Crop
U5-06 RSPF post-separation sensor trouble Crop
U5-07 RSPF read sensor trouble Crop
U5-08 RSPF SB sensor trouble Crop
U5-11 RADF paper feed motor operation Crop
U6-00 Desk/LCC communication trouble Empty trays of paper then Crop 15 or 14 where number 15 is not available (some MX and MXM models)
U6-01 Desk/LCC No. 1 tray lift-up trouble Empty trays of paper then Crop 15 or 14 where number 15 is not available (some MX and MXM models)
U6-02 Desk No.2 tray/LCC1 lift-up trouble Empty trays of paper then Crop 15 or 14 where number 15 is not available (some MX and MXM models)
U6-03 Desk No.3/LCC2 lift-up trouble Empty trays of paper then Crop 15 or 14 where number 15 is not available (some MX and MXM models)
U6-08 Desk 24V power abnormality Empty trays of paper then Crop 15 or 14 where number 15 is not available (some MX and MXM models)
U6-09 LCC lift motor trouble Empty trays of paper then Crop 15 or 14 where number 15 is not available (some MX and MXM models)
U6-10 Desk/LCC transport motor trouble Empty trays of paper then Crop 15 or 14 where number 15 is not available (some MX and MXM models)
U6-20 LCC communication trouble Empty trays of paper then Crop 15 or 14 where number 15 is not available (some MX and MXM models)
U6-21 LCC transport motor trouble Empty trays of paper then Crop 15 or 14 where number 15 is not available (some MX and MXM models)
U6-22 LCC 24V power abnormality Empty trays of paper then Crop 15 or 14 where number 15 is not available (some MX and MXM models)
U6-23 A3LCC tray lock detection trouble (Reverse Winding) Empty trays of paper then Crop 15 or 14 where number 15 is not available (some MX and MXM models)
U6-24 A3LCC tray lock detection trouble Empty trays of paper then Crop 15 or 14 where number 15 is not available (some MX and MXM models)
U6-28 LCT1 paper feed position abnormality Empty trays of paper then Crop 15 or 14 where number 15 is not available (some MX and MXM models)
U6-29 LCT1 lift-up trouble Empty trays of paper then Crop 15 or 14 where number 15 is not available (some MX and MXM models)
U6-33 LCT2 lift-down trouble Empty trays of paper then Crop 15 or 14 where number 15 is not available (some MX and MXM models)
U6-38 LCT2 paper feed position abnormality Empty trays of paper then Crop 15 or 14 where number 15 is not available (some MX and MXM models)
U6-39 LCT2 lift-up trouble Empty trays of paper then Crop 15 or 14 where number 15 is not available (some MX and MXM models)
U6-43 LCT3 lift-down trouble Empty trays of paper then Crop 15 or 14 where number 15 is not available (some MX and MXM models)
U6-48 LCT3 lift-up trouble Empty trays of paper then Crop 15 or 14 where number 15 is not available (some MX and MXM models)
U6-49 LCC incompatible trouble Empty trays of paper then Crop 15 or 14 where number 15 is not available (some MX and MXM models)
U6-50 Non-support trouble in automatic detection of option connection (Desk Unit) Empty trays of paper then Crop 15 or 14 where number 15 is not available (some MX and MXM models)
U6-51 Non-support trouble in automatic detection of option connection (LCC unit) Empty trays of paper then Crop 15 or 14 where number 15 is not available (some MX and MXM models)
U6-52 PCU PWB - Paper feed desk (paper feed tray 2) communication trouble Empty trays of paper then Crop 15 or 14 where number 15 is not available (some MX and MXM models)
U6-63 Manual feed tray lift-down trouble Empty trays of paper then Crop 15 or 14 where number 15 is not available (some MX and MXM models)
U6-68 Manual feed tray paper feed position abnormality Empty trays of paper then Crop 15 or 14 where number 15 is not available (some MX and MXM models)
U6-69 Manual feed tray lift-up trouble Empty trays of paper then Crop 15 or 14 where number 15 is not available (some MX and MXM models)
U7-00 PC/Modem communication trouble Crop 16
U7-50 MFPC PWB - Vendor machine communication error Crop 16
U7-51 Vendor machine error Crop 16
U9-00 Operation control communication trouble Crop 16
UC-02 CPT-ASIC abnormality Crop 16
UC-20 DOCC ASIC error Crop 16